Data Sheet


 User Manual


 Purchase
 
 


 Wireless Remote Control Transmitter/Receiver Set

 
Wireless Analog Voltage Transmitter/Receiver Set


Wireless Remote Control Transmitter System Model: DRWS-24-AV

Features

    Wireless Bridge Between Voltage Signal & Instrument

    0-1, 0-5, 0-10 and 0-20V DC Input/output Range

    Sold as Transmitter/Receiver Factory Match Set

    Adds Wireless Capability to Any Existing Application

    Up To 1 Mile Line-of-site Transmit/Receive Distance

    Enclosures Mount on Standard 35mm Din-rail Track

    Powered By 12-24V DC or 120V AC with Power Adapter

    License Free Point-to-point Radio Operation

Applications

Process Transmitter Signals, Valve Positioning & Control, Remote Sensor Monitoring


Description

Model DRWS-24-AV Wireless Analog Voltage Transmitter/Receiver Set provides a wireless bridge between any process voltage signal and a voltage input process monitoring or control Instrument. The voltage readings connected to the transmitting unit are sent via a license free radio signal to a receiver unit up to 1 mile (Line-of-site) away. The receiving unit reproduces an accurate analog voltage output that mirrors the voltage input signal to the transmitter. Four models are available with input/output ranges of 0-1, 0-5, 0-10 or 0-20V DC.


EXAMPLE: Level Transmitter Sending Readings to a Remote Process Meter
wireless remote control switch relay

General Specifications
Radio Frequency: ISM 2.4GHz
Regulatory: FCC Part 95 (No license required)
Transmitter/Receiver Code Matching: Factory set
Antenna Connection: RP-SMA
Wiring Connection: Terminal Blocks
Transmit/Receive Distance
(with included antennas):
Indoor/Urban 100ft, Line-of-site 600ft
Transmit/Receive Distance
(with optional antennas):
Indoor/Urban 300ft, Line-of-site 1 Mile
Operating Temperature: -22 to 113 F (-30 to 45 C)
Enclosure: Din-rail Mounted Plastic
Antennas: 5dbi, Omni-directional (Included)

Transmitter Specifications
Analog Input: 0-1, 0-5, 0-10, or 0-20V DC
ADC Accuracy: 10 bit
RF Power Output: 63mW
RF Data Rate: 250 kbps
RF Output Impedance: 50 Ohm nominal
Operating Power: 12 - 24V DC @ 3W max

Receiver Specifications
Analog Output: 0-1, 0-5, 0-10, or 0-20V DC
Output State if RF Signal Loss: Holds Last Reading
Receive Sensitivity: -100 dBm
RF Input Impedance: 50 Ohm nominal
Operating Power: 12 - 24V DC @ 3W max
Output: 0-1, 0-5, 0-10, or 0-20V DC

Regulatory Approvals
Regulatory: FCC Part 95 (No license required)
FCC(USA): OUR-XBEEPRO
IC (Canada): 4214A-XBEEPRO
Transmitter Operation Transmitter Operation The wireless analog voltage signal transmitter reads analog input data from any voltage source such as temperature, pressure, strain, flow, level or RH sensors and then sends the measured data over the air to a remote location. The measured voltage signals are converted to digital packets and then transmitted via a license free radio transmission to a waiting control receiver.
Receiever Operation Transmitter Operation The wireless voltage analog receiver decodes any incoming radio packets and converts them back into the same voltage signal that is being measured by the transmitter in real time.

Available Models
See Full Data Sheet For Additional Specifications.
Data Sheet
Each Wireless Transmitter/Receiver Set includes 5dBi Antennas, 9'Antenna Extension Cables, Antenna Mounting Brackets and User Manual.

Note: Continued product improvements make specifications subject to change without notice.
This product is approved for use in North America.